Last Updated: November 11, 2026
Quick Summary
A routing template is a flat, rigid pattern with a precise edge that guides a bearing-equipped router bit around a guitar body outline or cavity. Build one from MDF, plywood, or acrylic, transfer your full-size drawing, cut and sand it to the line, then test on scrap before routing a real body.
- Use 1/2-inch to 3/4-inch MDF or plywood for the template body; acrylic should be at least 1/2 inch thick.
- Measure bearing and cutting diameters with calipers; they must match exactly for a flush-trim bit.
- Take passes no deeper than 1/8 inch to reduce tear-out and bit deflection.
- Feed left to right, counterclockwise, to avoid climb cutting and kickback.
- Always run a test cut on scrap and check it against your template before routing the real body.
Table of Contents
- What a Guitar Body Routing Template Does and When You Need One
- Choosing a Guitar Body Shape and Drawing a Full-Size Outline
- Selecting Guitar Body Template Material: MDF, Plywood, or Acrylic
- Transferring the Outline and Setting Centerlines and Alignment References
- Cutting and Sanding the Template to Measured Tolerances
- Choosing Router Bits and Bearing-Guide Setup for Guitar Making
- Building a Guitar Body Routing Jig Around the Template
- Test Cuts, Accuracy Checks, and Troubleshooting Routing Errors
- Finishing Your Routing Template and Taking the Next Step With Your Build
- Frequently Asked Questions
Building a guitar body routing template is one of the most useful skills a home builder or repair tech can learn. A good template lets you cut the same body shape again and again, with clean edges and a tight fit. Get the template right, and your routing work becomes faster, safer, and far more repeatable. This guide walks you through the full process, from drawing the outline to troubleshooting your first test cut.
What a Guitar Body Routing Template Does and When You Need One
A routing template is a flat, rigid pattern that guides a router bit around the outline of a guitar body or cavity. A routing template is a shaped piece of material with a precise edge. A bearing-guided bit rides along that edge and removes the wood beyond it.

You need one when you want to:
- Cut the same body outline more than once
- Rout cavities for pickups, controls, and the neck pocket
- Reproduce a shape that is hard to cut freehand
- Keep the outline symmetrical from one body to the next
Skip the template if you plan to cut only once and by hand. For repeat work, the time you spend on a template pays back quickly.
Choosing a Guitar Body Shape and Drawing a Full-Size Outline
Start with a body shape you know well. A Stratocaster-style body, a Les Paul-style body, and a custom design each demand different levels of precision. Simple, symmetrical shapes make a better first project.
Draw the outline at full size on paper or in design software. Use a large sheet and mark the neck pocket location, the centerline, and the bridge position. These marks guide every later step.
- Print full-size guitar templates if you find a reliable pattern online
- Check that the outline is symmetrical about the centerline
- Measure your reference dimensions twice before you commit
Selecting Guitar Body Template Material: MDF, Plywood, or Acrylic
The material you choose affects durability, edge quality, and how well the bearing rides.
- MDF is stable, cheap, and cuts cleanly. It wears faster under heavy use, so it suits a first template.
- Plywood holds its shape well and resists wear better than MDF. Choose a void-free grade with smooth faces.
- Acrylic gives a clear view of your layout and a smooth, durable edge. It costs more and can crack if it is too thin.
Most builders use 1/2-inch to 3/4-inch thick stock for the template body. Thickness affects bearing contact, so keep it consistent across the piece.
Transferring the Outline and Setting Centerlines and Alignment References
Transfer your full-size drawing to the template blank. Use carbon paper, a pencil, or a pattern transfer method. Then mark the centerline and any reference points that must line up with the body blank.
Accuracy here matters more than speed. For a related guide on truss rod and neck alignment basics, see neck alignment basics. A mistake at this stage carries forward into every cut.
- Mark the centerline with a straightedge
- Mark the neck pocket and bridge references
- Double-check each reference against your full-size drawing
Cutting and Sanding the Template to Measured Tolerances
Cut the template slightly outside your outline, then sand up to the line. A jigsaw or bandsaw works well for the rough cut. Sand carefully with a spindle sander or a file, and check the edge against your drawing often.
A common mistake is sanding too fast and rounding the corners. Keep the sander moving and check your progress frequently.
Aim for a smooth, straight edge with no flat spots. Any bump on the template will show up as a bump in the routed body.
Choosing Router Bits and Bearing-Guide Setup for Guitar Making
A flush-trim bit with a top-mounted bearing is the workhorse for template routing, but the geometry of the bit and the thickness of your template must work together. To see how to pick the right jig for different instruments, read choosing the right jig for different instruments. The bearing rides on the template edge, and the bit cuts the blank to match. If the bearing is too small or the bit too short, the bearing will not contact the template properly, leading to inaccurate cuts or unsafe operation.

Key measurements to check before you rout:
- Bearing diameter vs. cutting diameter: For a flush-trim bit, the bearing diameter must match the cutting diameter exactly. If the bearing is smaller, the bit will cut into the template; if larger, it will leave a step. Measure both with calipers.
- Bit length and template thickness: The cutting length must be long enough to reach through the template and into the blank. A common setup uses a 1/2-inch shank bit with a 1-inch cutting length and a 1/2-inch bearing. If your template is 3/4-inch thick, the bearing will sit on top of the template while the bit cuts the blank below. Ensure the bit's cutting length exceeds the template thickness plus the depth of cut into the blank.
- Bearing placement: Top-mounted bearings are standard for template routing because the bearing rides on the template while the bit cuts below. Bottom-mounted bearings are used when the template is underneath the workpiece. Choose based on your jig setup.
Use shallow passes rather than one deep cut. A common pattern is to take passes of no more than 1/8 inch in depth. This reduces load on the bit, improves cut quality, and lowers the risk of tear-out or bit deflection.
Watch out: If the bearing is not fully seated against the template edge, the bit can grab and pull the workpiece, causing a kickback. Always ensure the bearing is in full contact before starting the router.
For template thickness, 1/2-inch to 3/4-inch MDF or plywood is typical. Acrylic templates should be at least 1/2-inch thick to resist cracking. The bearing must ride on a smooth, consistent edge; any imperfection in the template edge will be transferred to the workpiece.
The key setup measurements and common settings from this section are summarised below.
| Setup item | Guidance | Note |
|---|---|---|
| Bearing vs. cutting diameter | Must match exactly | Measure both with calipers |
| Typical bit setup | 1/2-inch shank, 1-inch cut length | Use a 1/2-inch bearing |
| Template thickness | 1/2 to 3/4 inch MDF or plywood | Acrylic at least 1/2 inch |
| Depth per pass | No more than 1/8 inch | Shallow passes reduce tear-out |
| Feed direction | Left to right, counterclockwise | Avoids climb cutting |
Building a Guitar Body Routing Jig Around the Template
Once the template is ready, build a jig that holds the blank and template together. Clamp the template firmly to the body blank, with the grain and centerline aligned.
Many builders add spacers or a base to raise the template above the blank. This gives the bearing room to clear the bottom edge.
Keep clamps away from the cut path. Check that the jig is stable before you start the router.
Test Cuts, Accuracy Checks, and Troubleshooting Routing Errors
Always run a test cut on scrap before you rout your real body. To judge how precise your work needs to be, see the repair quality checks guide. Check the result against your template and drawing. A complete accuracy check includes verifying symmetry, centerline alignment, neck-pocket fit, and repeatability. Measure the test cut with calipers and compare to your intended dimensions.
Common problems and fixes:
- Uneven edges: The bearing may be worn or the template may have a rough spot. Replace the bearing or resand the edge. Also check that the template is securely clamped; movement during the cut causes waviness.
- Burn marks: The bit is dull or you are cutting too fast. Sharpen or replace the bit and slow your feed rate. Burn marks often indicate that the bit is rubbing rather than cutting.
- Chatter or vibration: The bit may be too long for the application or the router speed too high. Reduce speed and take lighter passes. Ensure the workpiece is firmly secured.
- Tear-out: This occurs when the bit exits the wood grain. Use a backing board or score the cut line with a knife before routing. A down-cut spiral bit can also help on edges.
- Template movement: Clamps may be inadequate or the template may be warped. Use at least two clamps on opposite sides and check that the template sits flat.
- Off-center cavity: The template or reference marks were off. Recheck the centerline before you cut again.
Safety matters at every step. Wear eye and hearing protection, secure your workpiece, and keep your hands clear of the bit path. Feed direction matters: for most template routing, feed from left to right (counterclockwise around the outside of the template) to avoid climb cutting. Climb cuts increase the risk of kickback and should only be attempted with a router table and firm control.
Watch out: Never reach under the workpiece while the router is running. Always unplug the router before changing bits or adjusting the setup.
Finishing Your Routing Template and Taking the Next Step With Your Build
Once your template passes the test cut, label it with the body model and date, and store it flat so it does not warp. Sand and seal the edges if you plan heavy use. Check the template for wear before each new project.
With a finished template, you can rout each new body with confidence. The Atlas-C1 is a universal multi-function tool that protects stringed instruments from headstock damage during travel, shipping, or storage, and doubles as a pre-aligned repair jig for common headstock breaks. Current pricing depends on quantity, dates, and delivery, so visit the Atlas C1 website for current prices or a quote. Eligible buyers may qualify for a 10% product discount and free shipping.
The Science of Harmony through innovation and design Long Live the Six String™
Frequently Asked Questions
How do you make a guitar body routing template?
Start with a full-size drawing of the body outline, including the neck pocket and control cavities. Transfer the outline to a stable template material such as MDF or plywood, mark a centerline and alignment references, then cut the shape on a band saw or jigsaw about 1/16 inch outside your line. Sand to the line with a spindle sander or flush-trim bit so the edge is smooth and square. Test-fit the template against a scrap or test blank before using it on a finished body.
What material is best for a guitar body template?
MDF is the most common choice because it is stable, cheap, and machines to a clean edge. Plywood is tougher and holds screws well, which helps when you attach guides. Acrylic gives you a clear view of the workpiece but can chip under a router and costs more. Whichever you choose, pick a material thick enough to support the bearing and resist wear over repeated passes.
What router bit should you use with a guitar body template?
A flush-trim router bit with a bearing on the shank is the standard choice. The bearing rides against the template edge while the cutting flutes remove the wood. Match the bearing diameter to the template offset you planned, since the bearing position determines where the final edge lands. Use a bit with sharp, undamaged flutes and check that the bearing spins freely before each job.

